Category Archives: powertool

Basic Cisco UCS fault report

This will connect to a list of UCS environments in a text file, build the report for each one, then send a single email with the report for each environment. The report contains:

– Unacknowledged faults
– Hardware locator LEDs that are on (it’s common to forget to turn them off when the work is done)
– If you are short port licenses it will also do a report showing the relevant counts and for convenience output the serial numbers of the FIs.

You’ll have to make the usual changes to directories, email addresses, etc.

You can also grab the script from http://http://poshcode.org/3923 .

<#
.Synopsis
    Connects to multiple UCS environments listed in a text file and generates a basic fault report for each one, then sends one email with the results.  In the report are unacknowledged faults, hardware locator LEDs that are on, and if you are short on port licenses it will show that.  Variables and paths will have to be changed to match your environment.
#>

param($CredentialFile=$null)

if ($CredentialFile -eq $null) { Write-Host "Missing the path to the credential file." -BackgroundColor DarkYellow -ForegroundColor DarkRed; break }


#-----------------------------
# Prep
#-----------------------------
function Get-Now { (get-date -uformat %Y%m%d) + "_" + (get-date -uformat %H%M%S) }
if ((Get-Module -Name CiscoUcsPS) -eq $null) { Import-Module -Name C:\Ops\Modules\CiscoUCSPowerTool\CiscoUcsPS.psd1 }

#Static parameters
Set-Variable -Name ScriptDir   -Value "C:\Scripts" -Scope Local
Set-Variable -Name ReportPath  -Value "C:\Scripts\Reports\UCS_Fault_Reports" -Scope Local
Set-Variable -Name ReportFile  -Value "$($ReportPath)\UCS_Fault_Report_$(Get-Now).html" -Scope Local
Write-Verbose "`nStatic parameters`n-----------------`nScriptDir = $($ScriptDir)`nReportFile = $($ReportFile)`n"
$mailTo = "alertsdistgroup@yourcompany.com"
$mailFrom = "UCS_Fault_Reports@yourcompany.com"
$mailSMTP = "smtp.yourcompany.com"

If ( !(Test-Path $ReportPath) ) { mkdir $ReportPath }
. $ScriptDir\Hals_PSCredentials.ps1
# Setup credentials as described in https://batchlife.wordpress.com/2012/11/14/powershell-script-to-backup-a-cisco-ucs-fabric-interconnect-using-the-cisco-powertool-cmdlets/

$UcsCred = Import-PsCredential -Path $CredentialFile


#-----------------------------
# Start doing the real work.
#-----------------------------

Disconnect-Ucs 2>$null # Connect-Ucs will fail if you're already connected to a UCS

"<pre>" | Out-File -FilePath $ReportFile -Width 400
Get-Date | Out-File -FilePath $ReportFile -Append -Width 400

Get-Content C:\Scripts\Repo\StaticInfo\UCSs.txt | ForEach-Object { 
    Write-Output "=========================================================================================================="
    Connect-Ucs -Name $_ -Credential $UcsCred | select name,version,username,virtualipv4address | ft -a
    if ($DefaultUcs -eq $null) {
        $mailBody = @()
        $mailBody += "$(Get-Now) - Error connecting to UCS`n`n"
        $mailBody += $_
        Send-MailMessage  -From $mailFrom -To $mailTo -Subject "Backup-mUcs Error-- Failed connecting to $($Ucs)" -Body ($mailBody | Out-String) -SmtpServer $mailSMTP
    }
    else {
        Get-UcsFault | Where-Object { ($_.Severity -ne 'cleared') -and ($_.Ack -ne 'yes') } | sort lasttransition -Descending | select lasttransition,severity,status,type,dn,descr | ft -a
        Get-UcsLocatorLed | ? { $_.operstate -eq 'on' } | sort dn | select dn,adminstate,color,operstate,id | ft -a
        If (Get-UcsFault | Where-Object { ($_.Severity -ne 'cleared') -and ($_.Dn -match 'F0676') } ) { 
            "`n------ Port Licenses Needed ----------------------------------------------------------------------------"
            Get-UcsLicense | Select-Object Ucs,Scope,Feature,Sku,AbsQuant,DefQuant,UsedQuant,@{n="RemQuant";e={$_.AbsQuant-$_.UsedQuant}},Status,PeerStatus,OperState,GracePeriodUsed | ft -a
            Get-UcsLicenseServerHostId | select ucs,rn,hostid | ft -a
        }
        Disconnect-Ucs 
    }
} | Out-File -FilePath $ReportFile -Append -Width 400

"</pre>" | Out-File -FilePath $ReportFile -Append -Width 400

$body = Get-Content $ReportFile

Send-MailMessage  -From $mailFrom -To $mailTo -Subject "UCS Fault Report $(Get-Date)" -Body ($body | Out-String) -BodyAsHTML -SmtpServer $mailSMTP

Advertisements

PowerShell script to backup a Cisco UCS fabric interconnect using the Cisco PowerTool cmdlets

We’ve got several UCS environments and thought it’d be a good idea to back them up. ūüôā The script is designed to run as a scheduled task. The deployment instructions are in the script. Thanks to Dan and Nick for testing and correcting the instructions.  Hopefully I didn’t make the instructions more confusing when I sanitized the script for server names and the like.

You’ll have to make the usual changes to directories, email addresses, etc.

You can also grab the script from http://poshcode.org/3767 .

<#
.Synopsis
Does a backup of a single UCS target.

.Description
Uses the UCS PowerTool cmdlet 'Backup-Ucs' and does all four types of UCS backup.
Filenames include the UCS name, date/time stamp, and backup type.
The backup directory is set by a variable in the script. If it doesn't exist the script will create. Since the backup files are XML I recommend enabling compression on the directory.

.Parameter Ucs
The UCS environment to backup. This can be either an IP address or the DNS name.

.Parameter CredentialFile
The location of the credential file to log on to the UCSM with. Defaults to the current directory.

.Example
Backup-mUcs.ps1 -Ucs ucspoc -CredentialPath C:\Temp\credentials.enc.xml

.Notes
NAME: Backup-mUcs.ps1
AUTHOR: Chris Monahan
LASTEDIT: 8/7/2012
KEYWORDS: UCS, PowerTool

.Link
https://batchlife.wordpress.com/2012/11/14/powershell-script-to-backup/

Requires -Powershell Version 2.0
Requires -Cisco PowerTool Version 0.99
Requires -Hal Rottenberg's PsCredential functions: http://poshcode.org/501 & http://halr9000.com/article/531

#>

<# Instructions for one time setup are at the bottom of the script #>

param($Ucs=$null, $CredentialFile=$null)

if ($Ucs -eq $null) { Write-Host "Enter the name/address of the UCS you're backing up" -BackgroundColor DarkYellow -ForegroundColor DarkRed; break }
if ($CredentialFile -eq $null) { Write-Host "Enter path to the credential file." -BackgroundColor DarkYellow -ForegroundColor DarkRed; break }

#-----------------------------
# Prep
#-----------------------------
#Static parameters
Set-Variable -Name ScriptDir -Value "\\server\share" -Scope Local
Set-Variable -Name BackupPath -Value "C:\Backups\UCSM_Configuration_Backups" -Scope Local
Set-Variable -Name BackupTypes -Value ('config-system','config-logical','config-all','full-state')
Write-Verbose "`nStatic parameters`n-----------------`nScriptDir = $($ScriptDir)`nBackupPath = $($BackupPath)`nBackupTypes = $($BackupTypes)`n"
$errmailTo = "name@address"
$errmailFrom = "name@address"
$errmailSMTP = "emailserver"

If ( !(Test-Path $BackupPath) ) { mkdir $BackupPath }
. $ScriptDir\Hals_PSCredentials.ps1

$UcsCred = Import-PsCredential -Path $CredentialFile

#-----------------------------
# Start doing the real work.
#-----------------------------

# Connect to the UCS
Connect-Ucs -Name $Ucs -Credential $UcsCred -ErrorVariable errConnectingUcs| select Ucs,UserName,Version
if ($errConnectingUcs -ne $null) {
$errmailBody = @()
$errmailBody += "$(Get-Now) - Error connecting to UCS`n`n"
$errmailBody += $errConnectingUcs
Send-MailMessage -From $errmailFrom -To $errmailTo -Subject "Backup-mUcs Error-- Failed connecting to $($Ucs)" -Body ($errmailBody | Out-String) -SmtpServer $errmailSMTP
break
}

# Get one of each type of UCS backup.
ForEach ($type in $backuptypes) {
Backup-Ucs -Type $type -PreservePooledValues -PathPattern ($BackupPath + '\${ucs}_${yyyy}${MM}${dd}_${HH}${mm}_' + $type + '.xml') -ErrorVariable errBackupUcs
if ($errBackupUcs -ne $null) {
$errmailBody = @()
$errmailBody += "$(Get-Now) - Error running backup of type $($type)`n`n"
$errmailBody += $error[0]
Send-MailMessage -From $errmailFrom -To $errmailTo -Subject "Backup-mUcs Error-- On $($Ucs) backup of type $($type) failed" -Body ($errmailBody | Out-String) -SmtpServer $errmailSMTP
}
}

# Don't leave a stale session on the UCS
Disconnect-Ucs

<# One time setup

1- Copy script to SCRIPTHOST server for the datacenter you're working in.
$> copy \\server\share\Hals_PSCredentials.ps1 C:\Scripts

2- Log on locally to the SCRIPTHOST with the service account the script will run under in Task Scheduler.

3- If necessary install the Cisco PowerTool module and configure it to load automatically in the PowerShell profile.
a- The PowerTool module can be copied from \\server\share\Modules to the same directory on the local scripthost.
b- The PowerShell profile may not exist yet. If it doesn't create file in the path specified by the "$profile" variable.
$> notepad $profile
1- Add the line "Import-Module C:\Ops\Modules\CiscoUCSPowerTool\CiscoUcsPS.psd1"
2- Save and exit the file

4- Create the credential file containing the UCS login credentials to use in the script. The credential file can only opened by the Windows user account that created it. That's why you have to log on with the Windows service account used to run the task in Task Scheduler. The Windows credentials encrypt the file, and inside the file are the UCS login username and password. You can store the credential files in any directory you want. The directory in the example is for demonstration.
$> mkdir C:\Scripts\CredentialFiles
$> . \\scripthost\share\Hals_PSCredentials.ps1
$> $creds = Get-Credential # Username/password to login to the UCS with.
$> Export-PSCredential -Credential $creds -Path C:\Scripts\CredentialFiles\somename.enc.xml

5- Copy \\server\share\Scripts\Run_Backup-mUcs.ps1 to the vmscripthost you're setting up.
a- This is the wrapper script that will be put into Task Scheduler. It will call Backup-mUcs.ps1 for each UCS environment to be backed up.
b- Edit the script so that it has the correct UCS DNS name(s) or IP address(es) for the datacenter you're configuring this for.

6- Test the script interactively first by running Backup-mUcs.ps1 and then by running Run_Backup-mUcs.ps1.

7- Add Run_Backup-mUcs.ps1 into Task Scheduler and test.
a- For now copy the Task Scheduler settings for the job from what's in the \\scripthost Task Scheduler. May put the full instructions in later.

8- Verify the scripthost server is getting backed up somehow. Preferably as a normal OS level full backup by the backup group. The size of the backups for our UCS's so far for four UCS environments is 12MB a day.

#>

UCS port license report.

This is simple, but handy. ¬†It’s just some formatting around the PowerTool cmdlet¬†Get-UcsLicense. ¬†Then I either export it to a CSV or leave it on the screen, and I might wrap it in a loop to report on all our UCS FEs.

Below are two snippets.  First, connecting to one UCS and exporting to a CSV file.  And then connecting to several UCSs, filtering on UCSs that are short licenses, and printing to the screen.

Get-UcsLicense | Select-Object Ucs,Scope,Feature,Sku,AbsQuant,DefQuant,UsedQuant,@{n="RemQuant";e={$_.AbsQuant-$_.UsedQuant}},Status,PeerStatus,OperState,GracePeriodUsed | Export-Csv-Path "UCSLicenseReport_$($DefaultUcs | Select-Object -Expand Ucs)_$(Get-Now).csv" -NoTypeInformation


gc UCSs.txt | % {
   Connect-Ucs-Name$_-Credential$ucscred | select ucs,VirtualIpv4Address,username,version | ft-a
   Get-UcsLicense | Select-Object Ucs,Scope,Feature,Sku,AbsQuant,DefQuant,UsedQuant,@{n="RemQuant";e={$_.AbsQuant-$_.UsedQuant}},Status,PeerStatus,OperState,GracePeriodUsed | ? { $_.RemQuant -lt0 } | ft-a
   Disconnect-Ucs
}

Hope this helps

Chris